Click close lab exm question correctto answer this question
Overall Performance
![]() |
|
||||
---|---|---|---|---|---|
![]() |
|||||
|
|||||
|
12. Ensure that Yes is selected and click Next.
13. Set the default gateway value, and click Add.
18. Ensure that Yes is selected to activate the scope and click Next. 19. Click the Finish button to close the wizard and create the scope.
To configure the Gst-Lap laptop in the Lobby to obtain IP and DNS addresses automatically from the DHCP server:
Obtain DNS server address automatically
5. Click OK.
Your Score: 7 of 7 (100%) Pass Status: Pass
Elapsed Time: 4 minutes 48 seconds Task Summary
On Gst-Lap, configure an alternate IP configuration using 192.168.0.2 for the IP address
On Gst-Lap, configure an alternate IP configuration using 255.255.255.0 for the subnet mask
3. Select Internet Protocol Version 4 (TCP/IPv4), and then click the Properties button.
4. Record the current static values for the IP address, subnet mask, default gateway, and DNS server addresses.
7. Select User configured, and then fill in the values you recorded in step 4. Click OK.
8. Click Close.
4/14/16, 8:21 PM
question.
Use static DNS server addresses
Add 67.138.54.120 as a DNS server
1. In the notification area, click the network icon and click Open Network and Sharing Center.
2. Click the Local Area Connection link.
8. Click the DNS tab.
9. To configure DNS server addresses, click the Add button.
15. Click Close.
about:blank Page 4 of 14
Elapsed Time: 3 minutes 52 seconds
Configure 172.25.10.86 for the IP address
Use the following values for the TCP/IP properties:
|
|
---|---|
|
k Page 6 of 14 |
Explanation
Use the following values for the TCP/IP properties in this scenario: |
|||||
---|---|---|---|---|---|
Connection | Host address | Subnet mask | De | Default gateway address |
|
|
172.25.255.254 | 255.255.0.0 | 172.25.10.1 | 163.128.78.93 | |
192.168.0.254 | 255.255.255.0 | None | None |
![]() |
Question 6: | |||
---|---|---|---|---|
![]() |
|
|||
|
4/14/16, 8:21 PM
Set IPv6 Address to FC00:CBA9:8765:4321::10
Set Subnet Prefix length to 64
3. Right-click vEthernet (External) and click Properties.
4. Select Internet Protocol Version 6 (TCP/IPv6) and click Properties.
![]() |
|
|
|||
---|---|---|---|---|---|
![]() |
|||||
Your Performance
Your Score: 4 of 4 (100%) Pass Status: Pass Elapsed Time: 35 minutes 58 seconds Required Score: 100%Task Summary
about:blank Page 8 of 14
4/14/16, 8:21 PM
Both Steps 1 and 2 confirm that there is not a physical connectivity problem in the local network. The problem most likely is related to the IP configuration for the network.
3. In the Support Office, open the command prompt and use the
ipconfig /all command to check the Local Area Connection
configuration. You should notice the following problems:2. Right-click the CorpDCHP12 server and click Connect
(maximize the window for easier viewing if desired).3. In Server Manager, click Tools > DHCP.
5. In the Support Office, issue the ipconfig /renew command. This will request the new IP address information from the DHCP server, and it will reconfigure the settings for the Local Area Connection.
6. In the Support Office, use the ipconfig /all command to check the Local Area Connection configuration. You should notice the line for the default gateway is now correctly configured as 172.25.10.1.
8. In Office 1 and Office 2, repeat steps 5 through 7 to fix the problem [netpro2015_lab_questions_en.exm EXM_TRB_IP_CONF1]
![]() |
|
|||
---|---|---|---|---|
![]() |
||||
|
Your Performance
Your Score: 2 of 3 (67%) Pass Status: Not Pass
Confirm Laptop is connected to Internet
Explanation
In this scenario, the Gst-Lap laptop is configured with a static IP address for a different network. To resolve the issue, configure the laptop to request IP address information from the DHCP server:1. In the notification area, right-click the network icon, and click Open Network and Sharing Center.
7. Click Close.
Confirm the network status in the Network and Sharing Center or use the ipconfig /all command to check the Local Area Connection configuration.
![]() |
|
|||
---|---|---|---|---|
![]() |
|
|||
Click the Done Done button when you have found the information you need to answer the following questions:
• • What is the IP address of the default gateway for ITAdmin?
• • What is the IP address of the ISP Internet router?
• • What is the IP address of the PartnerNet router?
Explanation
[netpro2015_lab_questions_en.exm EXM_TRB_RTG_TRACE1]
![]() |
|
|||
---|---|---|---|---|
![]() |
||||
What is the default gateway address for ITAdmin
Click Done Done to answer the following questions:
How many routers are in the path between ITAdmin ITAdmin and the remote computer?
Your Score: 2 of 3 (67%)
Elapsed Time: 4 minutes 36 seconds
Obtain the IP address automatically
Obtain the DNS address automatically
In the Support Office:
Connect an Ethernet twisted pair cable to the Ethernet port
the Supp port on the patch panel and port 6 on the switch.
Complete the following steps:
2. Expand the Cables category in the Shelf, and select the Ethernet twisted pair cable.
3. In the Selected Component window, select a cable end. Drag and drop the connector to the Ethernet port on the computer.
9. Select Internet Protocol Version 4 (TCP/IPv4) and click
Properties.10. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK.
16. In the Selected Component window, drag the other connector to port 6 on the switch (top row, third column from the left).
17. To confirm the connection to the network and the Internet for the workstation, on Support click the networking icon in the System tray and open the Network and Sharing center. The Network and Sharing Center diagram should now indicate an active connection to the local network and the Internet.
Authorize the CorpDHCP12 as a DHCP server
Configure the DHCP scope
4. Right-click the CorpDHCP12 server; then select Authorize.
5. Expand the CorpDHCP12 server.
2. Set the subnet mask by typing the mask value (example:
255.255.255.0) or typing the number of subnet mask bits
(example: 24) in the Length field.3. Click Next.
14. To activate a scope, browse to and select the Subnet1 scope.
15. Right-click the scope and choose Activate.